High-Strength Concrete Columns in High-Rise Buildings
Strength and ductility of high-strength concrete columns were investigated by examining available test data. The results are summarized in terms of load and ductility capacities of columns....
Lateral Bracing Criteria of the Composite Braces
In order to simplify the hysteretic characteristics of diagonal steel braces, a lateral bracing problem of unbonded braces embedded in the concrete panel is treated here. Lateral bracing...
Shock-tested R. C. Slabs: Significant Parameters
Shock-tube tests of plain concrete and reinforced concrete (R. C.) slabs were performed. The influence of free water in concrete pores, emphasized in previous tests at a material level,...
Load Rate Effects on Concrete Compressive Strength
Plain concrete cylindrical specimens from six different concrete mixes, 51 mm in length and diameter, were tested in compression quasi-statically at strain rates between 10-6/sec...
Towards Structural Strength and Safety Evaluation Within Bridge Management Systems
Bridge management systems being implemented by transportation departments in the United States are limited in their ability to consider structural strength and safety when preparing recommendations...
Local Web Crippling of Unstiffened Multi-Cell Box Sections
Full-scale experiments and analyses show that the AISC/LRFD design equations for web yielding and web crippling strength of unstiffened webs, developed from test data on I sections, can...
Local Buckling of Pultruded FRP Beams: Theory and Experiment
A continuing experimental and theoretical investigation of the local compression flange buckling of commercially produced pultruded fiber-reinforced plastic (FRP) beams is briefly described...
Rational Limits for Longitudinal Steel in Concrete Columns
Current limits for the amount of longitudinal reinforcement in concrete columns were established more than 60 years ago. Commercial grades of reinforcement in 1930 were about half as strong...
High-Strength Concrete Columns: State of the Knowledge
This paper consists of reported information divided into two general categories, performance of High-Strength Concrete (HSC) columns under concentric loads, and combined axial and bending...
Evaluation of Wood Floor Vibration Design Criteria
In the United States, floors in wood buildings are designed according to strength and deflection criteria under static uniform loads. With the introduction of engineered joist products...
Strength Variability of Wood Formwork Members
Failure of concrete formwork is one of the main causes of concrete construction failures. Among the main causes of formwork failure is inadequate strength. Currently there is no published...
Unified Code Provisions for Concrete Bridges
Provisions on limiting the flexural reinforcement adopted in the new AASHTO LRFD Specification for Bridge Design are summarized (1). They address minimum and maximum levels of reinforcement...
Mechanical Behavior of Dowels Embedded in Concrete
In this paper an experimental investigation on the behavior of dowels embedded in concrete is described. The dowel strength under monotonic forces with two different boundary conditions...
A Self-Balancing Laminate
A self balancing wood laminate has been developed based on the principle of orthotropic elasticity. Lumber is cut into three sections in the flatwise plane and each side member is turned...
The Effects of Bolt Over-Tightening on Bolted Connections
This paper describes a portion of the research program being conducted on structural connectors which have been over-tightened. Direct-Tension Indicators (DTI) may be specified for use...
Externally Stiffened I-Beam to Box-Column Connections
This paper is concerned with I-beam to Box-column connections stiffened externally. Experimental and theoretical findings on full-scale connection models are highlighted. The performance...
Seismic Strengthening of URM Buildings with Steel Bracing
Unreinforced masonry (URM) buildings with large open fronts are extremely vulnerable to seismic inputs posing serious life safety hazard. Steel bracing systems have been used to upgrade...
Shear Design Guidelines for Polyester Concrete Using Recycled Plastic
Previous research on the shear behavior of steel-reinforced polymer concrete (PC) beams has been very limited and no efficient design procedures have been proposed. In all the previous...
Biaxial Testing of Brittle Repair Material for Rigid Pavements
Most codes of practice prescribe procedures for selecting patch configuration and material based on test devised for evaluating new pavement materials. This study is aimed at examined...
Testing of Hollow Clay Tile Masonry Prisms
This paper presents test results of 610-mm wide (24-in.) by 1219-mm high (48-in) by 203- or 330-mm (8- or 13-in.) thick prisms constructed of hollow clay tiles. Three prisms were extracted...
Return to search